TECKNET Wireless Keyboard and Mouse Combo Setup and Pairing Guide
By TECKNET official website | Published: 2026-10-13
Category: How-to Guides
Set up your TECKNET wireless keyboard and mouse combo in minutes. Step-by-step pairing for 2.4GHz and Bluetooth, plus fixes for common connection problems.
Quick answer
To set up a TECKNET wireless keyboard and mouse combo, first charge or insert batteries, then plug the 2.4GHz USB receiver into your computer or pair over Bluetooth. Turn both devices on and wait for them to connect automatically. If they don't, use the pairing button or key combination, and check that the correct input mode is selected.
Before you start: charge, batteries, and receiver check
A few minutes of preparation prevents most pairing failures. Confirm the keyboard and mouse have power: the TK-KB044 combo runs on batteries, while the TK-KB046 and vertical mouse are rechargeable via USB-C. If you're using the 2.4GHz receiver, plug it into a direct USB-A port on your computer, not a hub or monitor, which can cause intermittent dropouts. Keep the receiver in a stable spot; moving it later may require re-pairing.
How to pair the combo via 2.4GHz USB receiver
The 2.4GHz connection is the simplest and most reliable for a single computer. Insert the receiver, then slide the power switch on both the keyboard and mouse to ON. They should connect within a few seconds. If not, press the pairing button on the bottom of each device (or use the key combination listed in your manual) to force a reconnect. A solid light on the receiver or device usually indicates a successful link.
How to pair the combo via Bluetooth
For Bluetooth, turn on the keyboard and mouse, then activate Bluetooth pairing mode. On the TK-KB044, the keyboard supports dual Bluetooth and 2.4GHz, so you can pair it with a laptop or tablet while keeping the receiver for a desktop. Open your device's Bluetooth settings, select the TECKNET keyboard or mouse from the list, and confirm any on-screen code. Repeat for the second device if needed. Note that some combos share one Bluetooth channel; check your manual to see if keyboard and mouse pair separately or together.
Switching between devices and multi-device setup
If your combo supports multi-device pairing (like the TK-KB046 or the vertical mouse), you can toggle between three devices using a dedicated key or button. For example, the vertical mouse connects via BT5.0, BT3.0, or 2.4GHz and switches with a press. This is handy for juggling a work laptop and a personal desktop. Remember that only one device can receive input at a time; you'll need to switch manually when changing computers.
Fixing a wireless combo that isn't working
If the keyboard or mouse stops responding, first check the power switch and battery level. For rechargeable models, a full charge takes about 1.5 hours via USB-C. Next, try a different USB port or re-insert the receiver. If you're using Bluetooth, remove the device from your computer's Bluetooth list and pair again. Interference from other wireless devices (like Wi-Fi routers or USB 3.0 hubs) can also cause lag; move the receiver to a front port or use a short extension cable. Finally, some combos have a reset button or key combination to clear old pairings—consult your manual.
Step-by-step setup for your TECKNET combo
- Power up and prepare: Insert batteries or charge the keyboard and mouse fully. For rechargeable models, use the included USB-C cable and charge until the indicator turns off (about 1.5 hours). Turn both devices on using their power switches. Checkpoint: a blinking or solid light usually means the device is on and ready to pair.
- Connect via 2.4GHz receiver (if using): Plug the USB receiver into an available USB-A port on your computer. Avoid USB hubs or monitor ports. The keyboard and mouse should connect automatically within seconds. If not, press the pairing button on the bottom of each device. Common mistake: using a USB hub can cause dropouts; plug directly into the computer.
- Pair over Bluetooth (if using): Turn on Bluetooth on your computer or tablet. Put the keyboard or mouse into pairing mode (usually by holding a key combination or pressing a button). Select the TECKNET device from the list and confirm any pairing code. Checkpoint: if the device doesn't appear, ensure it's in pairing mode and not already connected to another device.
- Test and switch devices: Type on the keyboard and move the mouse to confirm they work. If your combo supports multi-device switching, press the designated key or button to toggle between paired devices. Common mistake: forgetting to switch the input source on the device you want to use; look for a dedicated switch key.
- Troubleshoot if needed: If input lags or stops, replace batteries or recharge, try a different USB port, and re-pair via Bluetooth. Keep the receiver away from metal objects and other wireless transmitters. As a last resort, reset the combo using the manufacturer's reset procedure. Checkpoint: a quick reset often resolves persistent pairing issues.
TECKNET combo models at a glance
- TECKNET Colorful Wireless Keyboard and Mouse Combo TK-KB044: TECKNET Colorful Wireless Keyboard and Mouse Combo TK-KB044 features retro-inspired typewriter-style round keycaps and a multi-color design, with flexible dual Bluetooth and 2.4GHz USB wireless connectivity. The dual connectivity means you can pair via Bluetooth to a tablet and still use the 2.4GHz receiver for a desktop, giving you flexibility without extra dongles.
- TECKNET Rechargeable Foldable Keyboard & Mouse Combo (Multi-OS), TK-KB046: TECKNET Rechargeable Foldable Keyboard & Mouse Combo (Multi-OS), TK-KB046 folds to 7.26×4.52×0.9 inches and has an aluminum alloy hinge rated for over 100,000 folds, plus ultra-quiet scissor-switch keys. Its foldable design and multi-OS support make it ideal for travel or hybrid work, and the quiet keys are considerate in shared spaces like libraries or open offices.
